Note and Disclaimer: Hydrogen or Hydroxyl gas and hydrogen cells are experimental technologies, results vary depending on application success is not guaranteed.

Contact us for a detailed proposal or secure your position for the next delivery dates. 907-830-8198

===== DUAL VECTOR SOLUTION  =====

DUAL-VECTOR HYDROGEN + TRIBOLOGICAL SOLID LUBRICANTS

Technology Architecture: Dual-Vector Synergy (Intake Oxidation via 12V/24V or 110V/220V Commercial HHO Injection + Go-Nano Boundary Lubricant Tribology)

MASTER TECHNICAL FOUNDATION & THERMODYNAMICS

Modern heavy-duty commercial diesel engines achieve a brake thermal efficiency typically between 42% and 50% under baseline operational parameters. Even in state-of-the-art prototype systems developed by manufacturers like Cummins and Weichai, which have achieved 53% to 55% thermal efficiency ceilings, nearly half of the chemical energy contained within diesel fuel is forfeited as thermodynamic waste before delivering usable mechanical work to the crankshaft.

Standard consumer gasoline engines convert only 25% to 35% of their chemical fuel into work. In heavy-duty industrial diesel power plants, the remaining 50% or more of fuel energy is lost across three specific thermodynamic pathways:

1. Exhaust Losses (25% to 30%): Escapes directly out of the exhaust stack as unburnt chemical energy, high-velocity thermal waste, and particulate carbon soot.

2. Cooling Losses (15% to 20%): Radiates into engine oil, water jackets, and cooling circuits to prevent structural metallurgical failure of the engine block and cylinder heads.

3. Pumping & Mechanical Friction (5% to 10%): Consumed by internal mechanical drag across bearings, valvetrains, piston assemblies, and critical accessory drives such as oil pumps and alternators.
   

The Problem of Incomplete Oxidation and Micro-Asperities

Up to 40% of internal mechanical engine friction occurs directly at Top Dead Center (TDC) turnaround. As the piston approaches TDC, its mechanical velocity slows to zero before reversing direction. At this moment of zero velocity, the hydrodynamic boundary oil film momentarily breaks down, causing ring-to-cylinder metal contact.

Simultaneously, the slow natural flame propagation velocity of diesel fuel (approximately 0.4 meters per second) prevents complete fuel oxidation within the limited crankshaft angle window near TDC. This incomplete combustion generates hard, unburnt carbon soot.

These microscopic carbon particles circulate within the crankcase oil and act like fine sandpaper, actively scouring cylinder liners, breaking down cross-hatch honing patterns, causing bore glazing, and destroying protective oil films. The resulting loss of ring-pack seal causes blow-by, elevated crankcase pressures, reduced compression efficiency, and increased fuel consumption.

The Dual-Vector Synergistic Mechanism

CBG USA and Go-Nano Lubricants combine combustion kinetics with boundary tribology into a self-reinforcing, closed-loop mechanical system:

Vector 1: Intake Oxidation 12/24V up to 110V / 220V Hydroxyl Injection

• Introduces a metered, on-demand stream of hydroxyl gas (66% pure hydrogen, 33% pure oxygen) directly into the engine's intake air charge.

• Acts strictly as a chemical combustion catalyst, not a primary fuel substitute. Hydrogen's flame velocity exceeds 2.5 meters per second, compared to diesel's 0.4 meters per second, accelerating the flame front by more than six times.

• Forces combustion to complete earlier and closer to Top Dead Center, shifting waste heat energy into downward crankshaft torque.

• Reduces un-burnt carbon soot, black smoke, and particulate formation by up to 70%, while reducing exhaust gas temperatures (EGTs) by 10°F to 25°F under continuous electrical and mechanical loads.

Vector 2: Surface Tribology (Advanced Nano Scale Solid Lubricants)

• Introduces spherical nano-scale tungsten disulfide (WS2) particles directly into the crankcase oil.

• Under extreme contact pressures and frictional heat exceeding 300,000 PSI at TDC, these sub-micron spherical particles embed into the microscopic valleys and asperities of the metal surfaces.

• Converts sliding boundary drag into rolling mechanical friction during zero-velocity piston turnaround.

• Dynamically seals the piston ring-to-liner interface, restoring cylinder compression, preventing blow-by, and extending oil service intervals by up to three times.

The Synergistic Feedback Loop: Lowering soot generation via intake oxidation prevents abrasive carbon particles from abrading the Go-Nano protective tribofilm. In turn, the preserved nano-tribofilm maintains higher dynamic cylinder compression, which ensures cleaner, hotter, and more efficient diesel combustion.